During knitting is often necessary to make the details of the product. To do this, knit fabric prepared correctly.
So the thing is to have a nice presentable and well lay down on the figure. What are the rules of cross-linking knitted parts?
The main secrets
1. Better use of the yarns from which the product is connected. An exception are not spun yarns decorated with, or in the form of a cord. In this case, the details need to sew flat strong thread of the same color.
Thread for stitching / istockphoto.com
2. Properly collect the product from the parts you need are met, a strict sequence of operations: to iron finished parts, give them to dry, sweep them up and try on the product to make sure it fits well.
3. Need to sew in the following order: the shoulder, the side seams and sleeves. The last thing sewed sleeves to armhole. Finalized finished product.
4. During the connection, do not use an overly long string. It should not be more than 45 cm.
5. When sewing is necessary to evenly pull the thread, and ensure that the seam forms a neat straight line.
Knit stitch with closed loops
This seam is almost invisible on the product. Crosslinkable parts laid out on a flat surface, they can be if needed to iron. The needle is inserted for the loop above the closed loops onto the top sheet. In the same way the needle is inserted into the loop of the lower row of the web. A few centimeters of the thread is tightened.
Knit stitch with closed loop / open sources
Knit stitch with open loops
Launched loop is picked up by the needle, and then captured the next loop and pulled the thread, after which you need to throw a loop with needles. At the bottom of the needle picks up stocking strap loop, and then is introduced the needle upwards capturing next loop, and the thread is pulled.
Knit stitch the open loop / open sources
The compound and equity transverse webs
According to the seam can sew some parts of the product: the back and sleeve, the sleeve and the front shelf. At the beginning of the needle is picked up by the loop and closed below the thread is pulled. Thereafter, the needle is inserted, picking broach between the edge and the next loop, and the thread is pulled. A few centimeters of the thread is tightened.
Equity and transverse web / open sources
Vertical seam to the front surface of
Necessary parts are placed on a flat surface, the needle is caught between the broaching edge and the first loop and the thread is pulled. On the other half of the product is picked up by broaching needle between opposite edge and the next loop, and the thread is pulled. After alternately repeating steps and, the thread is tightened by a few centimeters.
Vertical seam to the front surface of / open sources
Vertical seam seamy smooth surface
This seam is performed according to the same principle as the seam in the front. The needle is inserted into broach between the edge and the next filament loop and pulled. Then the needle is inserted into broach between the opposite edge and the next loop, and the thread is pulled.
Vertical seam seamy smooth surface / open sources
seam line
The joints must be below a series of closed loops to the front side could not see the closed loop. The needle with the thread is inserted between the hinges. Stitch is being back so that the working thread is on the wrong side forward, and displayed before the previous stitch at an equal distance from them.
Seam line / open sources
chain stitch
This chain consists of air loops. Chain stitch is often used when sewing on the knitwear, in the processing of the neck, armholes and bottom products.
The thread is attached to the underside of the leaf. The needle is displayed on the front side, by introducing it into the hole where the thread goes out, after throwing the main thread from right to left, to form a large loop. Then pulled out the needle, holding the thread with your left hand, and tightening the noose. To perform next stitch needle is inserted into the previous one. Each link should be as if coming out of the other. When the chain stitch need mandatory compliance stitches to each other in size.
Chain stitch / open sources
Kettelny seam
it is often used for sewing Beek, pockets, straps. Also, according to the seam is treated with horizontal cuts on the canvas or fix the last row of loops.
Before cross-linking of the product should be well to iron. Edge details must end three or four rows facial. Open hinges also carefully otutyuzhivayutsya. The needle is inserted from the inside into the second loop, then the first top and bottom is pulled further up through the third loop. Thereafter, the needle is inserted downwards again into the second loop and is pulled through the fourth from the bottom upward.
Kettelny seam / open sources
Special seam for stitching gum
The auxiliary thread to be used for provyazyvaniya two additional rows. Details need to steam with a wet gauze. After this series of auxiliary yarns are removed.
After the needle is inserted in the bottom 2, the first hinge part. Pull up the thread of the needle should be introduced in two respective hinge upper part, continuing to pull the thread. Staple one side of gum, you should close the loop on the other side. Then aligning both sides of the gum, it is necessary to insert the needle into the 2 adjacent loops of the bottom part. By introducing needle 2 in the respective upper hinge parts should tighten the thread.
Special seam for stitching gum / open sources
also read ABC needlewoman: all the secrets of knitting
